At Lorigo Plumbing Supplies LLC, we are dedicated to providing high-quality roofing supplies to our customers!
Check out our new product:
Wet N' Dry Roofing Cement
#1 PREFERRED BY EXPERIENCED ROOFERS
This product is a heavy-bodied mastic for repairing and patching built-up roofs, flashings and masonry cracks for maintaining all types of roofs!
PRODUCT NO. 4000 FLEXA-COAT is an acrylic elastomeric roof coating with maximum dirt pickup resistance. Designed for maximum protection against sun and extreme weather.
should not be applied over 100% silicone.
Roof substrates must be clean, dry, free of all debris, and any contaminants which would impede proper adhesion. A pressure wash
PRODUCT NO. 4000 FLEXA-COAT is an acrylic elastomeric roof coating with maximum dirt pickup resistance. Designed for maximum protection against sun and extreme weather.
should not be applied over 100% silicone.
Roof substrates must be clean, dry, free of all debris, and any contaminants which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings products. When applying over aluminum roof coating, asphalt, tar, hot applied built-up roofing, granulated cap sheet and metal roofing systems, one coat of PRODUCT NO. 295-G STAIN SHIELD or PRODUCT NO. 297-X X-TREME must be applied prior to the application of PRODUCT NO. 4000 FLEXA-COAT. All large cracks and seams should be repaired by embedding one layer of polyester fabric between two layers of PRODUCT NO. 501-W-P ACRYLIC MASTIC or PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC prior to application of PRODUCT NO. 4000 FLEXA-COAT. To achieve proper adhesion over TPO, PVC, EPDM or exposed Spray Polyurethane Foam, one coat of PRODUCT NO. 297-X X-TREME must be applied prior to any Tucson Rubberized Coatings repair or topcoat products. Tucson Rubberized Coatings Products should not be applied when freezing temperatures or rain is expected within 24 hours of completed application. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present.
Clean brushes, tools and other equipment with warm soapy water immediately after use. Dried film may require paint remover.
40" x 324', Heavy Duty, Polyester Mesh, Contouring Roof Fabric, Use For Reinforcing Flat Or Low Pitch Roof Areas, Especially For Flat, Rough Or Uneven Roof Surfaces With Standing Water, Contours & Shapes To The Surface & Extends The Life Of Roof Coating, Increases Strength Of Coating Up To 1000 Psi, Absorbs 1-1/2 To 2 Gallons Per SQFT Of Coating To Lay It.
DESCRIPTION. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is an elastomeric premium quality white sealing compound designed for use in the waterproofing of roof flashings. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is reinforced with polyester fibers for maximum strength and durability while remaining flexible.
USES. PRODUCT NO. 510 REINFORCE
DESCRIPTION. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is an elastomeric premium quality white sealing compound designed for use in the waterproofing of roof flashings. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is reinforced with polyester fibers for maximum strength and durability while remaining flexible.
USES. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can be used as a patching compound or flashing mastic for sealing around roof penetrations, pipes, skylights, ductwork, or filling gaps in parapet walls with excellent adhesion to most roofing substrates. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can also be used in conjunction with a polyester fabric for added strength around penetrations, drains, scuppers, and skylights.
SURFACE PREPARATION. Roof substrates must be clean, dry, free of all debris, and any contaminates which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. Metal panels where the structural integrity has been compromised should be removed and replaced with like panels. Over aluminum roof coating, apply one coat of PRODUCT NO. 295-G STAIN SHIELD or PRODUCT NO. 297-X XTREME prior to the application of PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC. Over TPO, EPDM, and PVC apply one coat of PRODUCT NO. 297-X X-TREME prior to the application of PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC. A bleach and water solution (1 part bleach to 2 parts water) should be used to treat any roof areas that have mildew or algae. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings restoration products.
APPLICATION. Proper protective clothing and PPE should be worn when applying products. It is normal to see a small amount of separation when first opening a pail. If necessary, gently mix the product with a trowel or paddle mixer, being careful to not introduce air into the product during mixing. PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC can be applied with a stiff paint brush or trowel in conjunction with a polyester fabric for reinforcement. Do not dilute product. While PRODUCT NO. 510 REINFORCED ACRYLIC MASTIC is white and UV stable, to extend its life it is recommended that it be coated by one of Tucson Rubberized Coatings topcoats. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present.
DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.